A pochade box is a portable small painting box you can take with you when painting plein air. The one I made has a small palette that fits inside, holes to insert paint brushes while working, and room for storage of supplies.
If I were to buy a pochade box new it would cost at least $150. There are a number of blogs that show how to make one of your own with cigar boxes and I have a friend that smokes cigars and is generous with giving them away. You can also find them online or from smoke shops for $5-10. I gathered my supplies over the course of a few months, here and there. In the end it probably cost me about $30 in supplies. As I said the cigar boxes were free and I already had the tripod. You could also look online at as http://www.freecycle.org/ in your area.
- Three cigar boxes. I had two the same and one oddball but similar in size to the other two.
- Small Hinges
- Small bungee cords
- Eye-and-Hook closure
- Odd scraps of cedar wood found inside of cigar boxes – for palette shelves inside of box and for inserting t-nut into. I fyour box does not come with extra pieces of wood, you can always repurpose rullers etc…
- 4-Bull clips – 1″ wide
- Skill Saw
- Dremel Tool – with small drill bit, and sander attachments
- Drill – with a variety of size drill bits to for brushes
- Linseed Oil
- Rag/Paper Towel
- T-Nut – either 1/4X20 or 1/4″X20X5/16″
- Wood Glue
- Mending Strips – for hinge on side of box
- Small Screw – to join mending strips
- Wing-Nut – to fit small screw
- Small flat screw driver – from set used for computer/sewing machine repair
- Standard camera tripod with extend-able legs
The first thing you will want to do is to replace the hinges and closure on the box you use. The ones put on cigar boxes are almost always weak and break easily.
Take apart the third odd ball sized cigar box and with skill saw, cut a square palette that will fit into the bottom of the other boxes.
Draw out the placement for the thumb hole. Use a Dremel Tool attachment or drill to make a hole in the center of the marked area. Using the Dremel Tool or Skill Saw cut out the shape desired. Note: Of everything, this step probably took me the longest.
Once you have the size correct of palette and thumb hole sand the edges down smooth with either sandpaper or with the Dremel Tool.
Inside of all the cigar boxes were thin strips of wood that could be pulled out. I took three strips and layered them together with wood glue, clamped them with the bull clips until dry. It should be plenty dry in a couple of hours.
This create a piece of wood approx 1/2″ thick. I then used the skill saw to cut an approximately 2×3″ shape.
Drill a hole in the center of the wood with a 1/4″ drill bit.
Insert the t-nut into the hole and tap it down with the hammer until the larger flat side is flush with the wood.
Attach the piece of wood with the T-nut slightly more to toward the top of the box as shown. Due to the wight of the lid and a small canvas it will help to balance it when on the tripod.
I put the mending strips on one side only. But you can put them on both if you want. I may wind up later doing that myself. Attach them as shown.
When the box is open, remove the wing-nut, use it and the small screw to connect the two strips. This will give you the ability to choose the angle of your lid, or easel.
I used several layers of thin linseed oil on the palette to seal and season it before using. I think it gave it a nice aged looked :0) To do so you simply rub in a thin layer of oil and allow it to dry, and repeat a few times.
This also shows the mending strips in use.
Figure out how tall to make your scraps of square wood to enable the palette to rest inside of the box and not sit taller than the edge. Glue each in a corner with wood glue.
Carefully take off the hinges off the other box that is the same size as the one you are using. On one of the half drill holes to insert the handles of your brushes, while painting. You probably will not be taking too many brushes with you so if you have a variety of sizes of 5-7 holes that will be more than enough. Test them out with the brushes you know you want to use and make necessary adjustments.
You need to do something that will keep the lid from smacking up against the inside of the lid. Especially when the palette is covered in wet paint, and you don’t want to have to clean it off each time out in the field. To help with this I put four thick buttons, one on each corner area to act as spacers. I plan on also using a piece of wax paper, to keep the lid and palette from sticking together during travel.
Three layers, one with holes for brushes, the box you just created, and the other side of a box. Wrap all three with the small bungee cords to keep secure. Inside of the two outer boxes you can store your paints, brushes, rags, 4 bull clips etc…
Consider cutting down the handles of a paint brushes that do not already fit.
I chose to have a designated plein air kit:
- The box materials I just created
- A small jar to carry mineral spirits
- Small jar of linseed oil (and/or any other medium I choose to use)
- Plastic bag (to place dirty rags into)
When out in the field attach the box to your tripod, take the two extra halves and attach them with the bull clips and use your lid as an easel.
NOTE: I have seen ones with special attachments for the easel portion. And I may try something similar in the future. Right now I plan on working fairly small and as portable as possible so this should work for now.
If you decide to build your own or have already and want to share, let us know! Either post links below or email us at firstname.lastname@example.org